APPLICATIONS / SUCCESS STORIES
ALL YOUR DATA LOGGING REQUIREMENTS COVERED
|
EMS System through Yokogawa Smartdac+ & Mirrihia Software
EMS systems plays a vital role in providing a validated back up to site Building Management Systems (BMS). Be it Cleanroom Monitoring, Product Storage, Incubation or Stability Chambers having a reliable back-up of this logged data is critical to the integrity of the system. IPP specialise in offering a turnkey EMS system through the Yokogawa Smartdac+ series with enhanced Data Integrity functionality. And now with increasing demands for easy access to site wide data, we now offer Mirrhia EMS software, bringing all of your EMS related data, Alarm Management & Reporting into one easy to use interface. 
Yokogawa EJX510A and EJX530A Absolute and Gauge Pressure Transmitter with Wika 990.22 Diaphragm Seal (P1S)
The high performance Yokogawa absolute and gauge pressure transmitter EJX510A and EJX530A feature single crystal silicon resonant sensors and are suitable to measure liquid, gas, or steam pressure. EJX510A and EJX530A output a 4 to 20 mA DC signal corresponding to the measured pressure. It also features quick response, remote setup and monitoring via HART communications.
| ||||
|
Burns Engineering Wall Temperature Assembly
The perfect fit for Facilities Monitoring in BioPharma and Pharmaceutical manufacturing. A high accuracy full immersion RTD wired to a Temperature transmitter with HART connectivity enclosed in a polished Stainless enclosure with IP67 rating.
| ||
CONDUCTIVITY CALIBRATION WITH AN INSACAL MASTER METER
|
Insacal Conductivity Master Meter with Accredited Calibration
With an INSACAL master meter you get a very flexible calibration tool. You can calibrate by closed loop procedures or in an open beaker. This allows you to choose whether your cell is calibrated on-site, in-situ or not.
| ||||
SECULIFE FUNCTION TESTERS
|
Medical Testing Technology at its finest
SECULIFE function testers have been specially developed for testing those medical devices which are used most commonly in clinics – directly at the patient. Great importance is placed upon efficiency and reliability when performing measurements on these devices. The great variety of manufacturers and models of monitoring and therapeutic devices also necessitates high levels of compatibility.
| ||
HAMILTON BEVERLY - THE FIRST PORTABLE METER TO MEASURE DISSOLVED OXYGEN
|
Hamilton Beverly for accurate and continuous measurement of Dissolved Oxygen
Beverly is designed for at-line and laboratory use to provide excellent reliability in a rugged design, and purpose built to handle the environmental extremes encountered in everyday brewing operations. Superior performance at an affordable price is achieved using Hamilton's best in class optical sensor VisiFerm DO B with built-in intelligence, making Beverly the brewer's best friend.
| ||
FLUKE'S TRIPLE POINT OF WATER IS PERFECT TO VERIFY PROBE ACCURACY
|
Fluke Triple Point of Water to verify
accuracy of thermometer probes FLUKE’s Triple Point of Water, a Primary Standard in Temperature Calibration, is the perfect solution to problems of backwards traceability when thermometers are found to be out of specification. Many of Ireland’s Pharmaceutical and Medical Device manufacturers use the Fluke TPW to verify the accuracy of their thermometer probes on a weekly or monthly basis. It is a simple one-point check to ensure no drift has occurred.
| ||
BY USING THE YOKOGAWA UT35A, IT PROVIDES A COST EFFECTIVE SOLUTION FOR PH APPLICATIONS.
|
pH Control and Wash System for 2 - Wire Transmitter Using Controller with PLC Function
pH wash systems are a requirement for many industries where electrode fouling is common place. Large amounts of deposits form over a period of time preventing the sensors performing correctly. This results in measurement loss and repeated expensive electrode replacement. It is difficult to apply wash systems to 2 wire transmitters due to hazardous area restrictions therefore incorporating the wash function within a control device outside the hazardous area provides an cost effective solution.
| ||
HOSPITAL STERILISER AND WASHER/DISINFECTOR
|
IMS System for Sterilisers
IPP have successfully implemented an IMS system for Sterilisers (Autoclaves) and Washers/Disinfectors in Irish hospitals to provide secure cycle data for traceability of surgical instrument sets (RIMD) from Theatre/Surgery and back through the Central Sterile Service Department (CSSD) or Hospital Sterile Supply Units (HSSU) for decontamination.
| ||
CIP PROCESS IMPROVEMENT
|
Measuring Conductivity correctly in
clean-in-place (cip) system Yokogawa's FLXA 21 Inductive Conductivity Transmitter has earned a reputation in the recovery of cleaning solutions because it can take measurements with good boundary surface precision over a wide range. This reduces operating costs and optimises cleaning and sterilising.
| ||
PERCENT CONCENTRATION MEASUREMENT IN FOOD APPLICATION
|
Percent Concentration Measurement
in Food Application This Application Note is designed to guide you through the programming steps required. All of the steps you will follow are in your ISC450 Instruction Manual, but we have pulled out just those steps that deal with setting up percent concentration using one of the “built-in” tables.
| ||
INFRALAB MEAT ANALYSER
|
InfraLab Meat Analyser - Fast Analysis of Fat, Protein, Moisture and Collagen
The InfraLab e-Series at-Line or bench-top meat Analyzer from NDC provides rapid accurate measurement of fat, moisture, protein, collagen and collagen/protein ratio in virtually any raw meat product. Easy-to-use, the InfraLab Meat Analyzer requires no special operator skills, and takes just 10 seconds to make the analysis of parameters which are key to the efficient production of consistent batches. Accurate measurement of these parameters enables proccessors to achieve consistent quality.
| ||
IN-LINE MOISTURE ANALYSER
|
Maximising dryer performance in the Dairy Industry
Our optimized Moisture, Fat and Protein measurements for the Dairy Powders Industry deliver real-time analysis and measurement of these three key parameters to enable process control for improved productivity and product quality and consistency. On-Line Measurement of dairy powders reduces the need for routine laboratory testing and helps ensure "Right-first-time" production. Using an accurate moisture measurement to monitor and control the drying process helps achieve energy savings by avoiding overdrying.
| ||
|
pH Buffer Solutions
All calibration procedures assume that the labeled values of the calibration buffers are correct. But buffer values can change over time and so can your results. A complete range of patented buffer solutions provides pH stability up to 5 years, something never achieved before. The pH buffers 9.21 and 10.01 are even stable in air. High buffering capacity provides rapid, stable calibration. The growth of fungus and micro-organisms is prevented. An important issue for the production of Certified Reference Materials is to ensure traceability through an unbroken chain of comparisons to reference material of the highest metrological quality (Primary Reference Material) from NIST1 and PTB2. Unlike other manufacturers, where only topdown traceability is applied, Hamilton works with circular or closedloop traceability, providing unique reliability of Hamilton DuraCal buffers.
| ||